Window Motor?

mespock

mespock

Marxists - Socialists
Joined
Jun 15, 2004
Messages
13,765
Reaction score
22
Location
Madison, Wisconsin, United States
Ok, who's taken out a window motor on a Mark VII?

How the :q do you get the motor off?

Where is it connected to the door? Yes, I see the motor at the bottom of the door -

I have the door pannel off and looking for where the motor gets mounted. I see the motor, but since it is inside the door I can't see or feel where the motor is bolted to the door, and who to remove it.

I see were the regulator is attached but fustrated that I can't find what is holding the motor on.
 
yes, i do believe you have to drill those rivets (make sure you have replacement bolts). Enough for the regulator assembly to swing over to an opening in the door panel where you can remove it from the regulator. As always observe caution. The regulator assembly is spring loaded and the window is heavy!!
 
Found this on another site:

POWER WINDOW GEAR REPLACEMENT - OPTION 1
Submitted by pro-five-oh / 10-18-01 (Some info courtesy of Yahoo Lincoln Group)

Doesn't the author look familar? :gr_hail: (pro-five-oh) Seems to answer a lot of tech questions. :steering:

"This is actually pretty easy and straight forward. First of all get the inside door panel off and take a look at the inner door skin. Put your hand inside the door cavity and locate the window motor.

Feeling between the door inner panel and the motor, locate the heads of the screws that attach the motor to the window regulator assembly. Adjacent to these screw heads, you should notice a dimple in the door inner panel sheet metal. Dimple is about 3/32" in diameter, and about 1/16" deep. There should be three(3) of them, one for each attaching screw.

Using a drill bit, or progressively larger drill bits, or better yet, a piloted 1/2" hole saw (the pilot is a 1/4' drill bit), drill three(3) holes big enough to clear the 5/16" socket required for the screw heads.

Use the 5/16" socket to remove the three screws attaching the window motor assembly to the regulator assembly.

Trace the motor lead wire to the outside of the inner door panel, and disconnect.

Reach inside the door cavity and pull or lift the motor off of the window regulator assembly. Snake it out through the opening that you are reaching in through.

Replace the motor assembly into the door cavity and mount it to the regulator assay. I use one of the devices that is commonly used to extract or pick up small screws or items that have fallen into hard to get at spaces. As you push the plunger forward, the end opens up with four (4) small fingers which can grasp the small screws, and allow you to put them through the holes and start the threads in the housing. Install and tighten all three attaching screws.

Reconnect the electrical connection, and try the motor function."
 
Yea, glad you found that mespock. You do not need to pull the regulator to take care of the motor. While you are in there, lube the regulator and gear with real whit lithium grease. Don't use the spray on stuff, use the real grease. That will help keep the motor running well for a lot longer.
 
Feeling between the door inner panel and the motor, locate the heads of the screws that attach the motor to the window regulator assembly. Adjacent to these screw heads, you should notice a dimple in the door inner panel sheet metal. Dimple is about 3/32" in diameter, and about 1/16" deep. There should be three(3) of them, one for each attaching screw.

I can only see one dimple. Does anyone know where I will find them incase I am just missing them.

There is another but it is so low on the door that I am not sure it is actually one. It is in the area of the window motor and where a screw could be.
 
There should be three noticable dimples at the bottom of the door, right where the motor is on the inside.
 
Motor went in easy. :tongue: I will post pictures of where to find the dimples and the whole. Plus Bit actual bit size I used.

Thanks to all for the help! :Beer

Now the only thing left to do is to recharge the AC and I will have a complete classic old school ride. :steering

Driving happy now that I can cop the lean witht he window down.

mespock said:
Found this on another site:

POWER WINDOW GEAR REPLACEMENT - OPTION 1
Submitted by pro-five-oh / 10-18-01 (Some info courtesy of Yahoo Lincoln Group)

Doesn't the author look familar? :gr_hail: (pro-five-oh) Seems to answer a lot of tech questions. :steering:

"This is actually pretty easy and straight forward. First of all get the inside door panel off and take a look at the inner door skin. Put your hand inside the door cavity and locate the window motor.

Feeling between the door inner panel and the motor, locate the heads of the screws that attach the motor to the window regulator assembly. Adjacent to these screw heads, you should notice a dimple in the door inner panel sheet metal. Dimple is about 3/32" in diameter, and about 1/16" deep. There should be three(3) of them, one for each attaching screw.

Using a drill bit, or progressively larger drill bits, or better yet, a piloted 1/2" hole saw (the pilot is a 1/4' drill bit), drill three(3) holes big enough to clear the 5/16" socket required for the screw heads.

Use the 5/16" socket to remove the three screws attaching the window motor assembly to the regulator assembly.

Trace the motor lead wire to the outside of the inner door panel, and disconnect.

Reach inside the door cavity and pull or lift the motor off of the window regulator assembly. Snake it out through the opening that you are reaching in through.

Replace the motor assembly into the door cavity and mount it to the regulator assay. I use one of the devices that is commonly used to extract or pick up small screws or items that have fallen into hard to get at spaces. As you push the plunger forward, the end opens up with four (4) small fingers which can grasp the small screws, and allow you to put them through the holes and start the threads in the housing. Install and tighten all three attaching screws.

Reconnect the electrical connection, and try the motor function."
Click to expand...
 
mespock said:
Now the only thing left to do is to recharge the AC and I will have a complete classic old school ride. :steering

Driving happy now that I can cop the lean witht he window down.
Click to expand...
Did somebody say OldSchool?

Try this on for (window) size:

oldschool3012.jpg
 
89 lsc window motor change

Just pulled door panel off to get a look at things. It looks tight and my problem is my window is full down. Is there any way of raising it before I try to change the motor? Can I change it with the window full down? Appreciate any help.
 
tinkerin with lincoln said:
Just pulled door panel off to get a look at things. It looks tight and my problem is my window is full down. Is there any way of raising it before I try to change the motor? Can I change it with the window full down? Appreciate any help.
Click to expand...

Welcome.

It's a a little involved but if you can use a drill and a nut driver, then you too can replace the window motor or just rebuild the window motor gear box.

See:
http://www.thelincolnmarkviiclub.org/tech/powerWindowMotorRepair.pdf
and
http://www.thelincolnmarkviiclub.org/tech/powerWindowMotorReplacement.pdf

oldschool3082.sized.jpg
 
You must log in or register to reply here.

Members online

Total: 72 (members: 1, guests: 71)
Back
Top