Do you have a price for the whole vehicle. I have an 05 with a crushed bumper ,basically everything below the hood all the plastic is toast but my engine tranny still solid
yaa and a martian that parked in a garage and a dumb ass crew that got stranded on an island.
No wonder the Russians;) used to think we were pushovers:D
how much do you want for drivers seat cover with the perforation holes and the back upright cover. and of course to cover shipping. need to replace mine too many tears
Do any of you factory ford/lincoln guys know if there are any differences between the 2005 LS and the 2006 LS factory service manuals besides the date. Did they change anything except the outside trim Right now I can get 3 set 2006 A&b and a wring manual for $40 the 2005 prices are over $90, I...
I have to replace my DCCV this weekend. My factory manual says to "disconnect the quick-couple disconnect hoses" Is there a trick to it or do need a special tool ,like when disassembling fuel lines. Unfortunately I will be outside with the job this weekend temp 45* ?rain /drizzle.[ Garage...
Patience grasshopper, the right people may have not noticed it yet. guys like joegr and 1 loudls and others are very knowledgeable . They might not have been on line yet. scroll some of the other posts about cooling issues. Unfortunately I have just gotten my LS 2 months ago so I am not very...
Hey drag 214, where was that salvage yard you got the parts from? Got a name or address. Did you notice if any gen2 there . Is it a pull your own or do they have to get the items for you. I'm in Tennessee and hard to find large yards with a lot of vehicles like ours. Oh and thanks for serving...
On a slight change of topic but still Gen1 to Gen 2. Do you guys know if the unibody is the same on both vehicles.Did they change/modify the suspension or can they just swap over those components. I have a line on a 2005 LS 3.9 that might come with a salvage title. It has 35,000 miles, I checked...
I have not seen the bushings only sold separately only with the whole control arm. Maybe others on the site might know if you can. A lot of knowledgeable people here. They run about $105 on Parts Geek or RockAuto. Not sure why you can get them for the rears but i did notice that the rear arms...
Thanks again to blueberryyum. found some listings on this sights and found parts geek etc order on its way. Now if I can remove the parts above it just to get a clear shot at it.
Thanks. Did not know that there were 2 heater cores. That makes more sense now. About that DCCV can you get it aftermarket or only from ford dealer. I may have to scrounge in a salvage yard. I'll browse around the forum also. Had seen many posts on the DCCV.
Ok guys (generic) I know there are some girls out there also. I am not sure where to start. I do have factory repair manuals but still a little unclear where to start as these areas are hard to access I have a 2000LS 3.9 w 143k on it . driving back from Birmingham Al. 200mile trip with the AC on...
Sorry to hear of the misfortune. I had a similar issue. I just bought my 2000 Ls and noticed the uneven tire wear on the left front.Since I plan to replace all suspension parts in the next few months, I went to assess the part. I snapped a wheel stud getting the wheel off. The garage that...
Well not sure if they had a typo for "air conversion" heck the local auto parts place looks up parts on computer and does not know what parts are compatible. In the old days 60s-70s the counter guy knew off the top of his head what part or sizes fit what and what years cars changed their parts...
I did try to reset the change oil soon but when I immediately try to push the reset and hold it it cycles to the next item ac filter change. Star power you might be right, I have a lead on the switches on E-bay.
On a similar note when I start the car the right side dash warning display will chime while it cycles thru all the warning about doors closed lights etc. It takes a minute and usually stops if I hit status or fuel after I have traveled maybe a quarter to half mile. I did change the oil but the...
If you want to get the scratch out try looking up micro surface finishing products on google. Years ago i used a kit ran about $85 dollars then but I used it on a plastic motorcycle headlight lens that a buddy dropped slid down the road. This got 95% out and they were deep 1-2mm. Course it...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.